FEDERAL MINE SAFETY AND HEALTH REVIEW COMMISSION
601 New Jersey Avenue, NW, Suite 9500
Washington, DC 20001-2021
Telephone No.: 202-577 6809
Telecopier No.: 202 434 9949
March 28, 2011
OAK GROVE RESOURCES, LLC., Contestant v. SECRETARY OF LABOR, MINE SAFETY AND HEALTH Respondent SECRETARY OF LABOR, MINE SAFETY AND HEALTH ADMINISTRATION (MSHA), Petitioner v. OAK GROVE RESOURCES, LLC., Respondent |
: : : : : : : : : : : : : : : : : : |
CONTEST PROCEEDING Docket No. SE 2009-261-R A.C. No. 7696616; 01/08/2009 Oak Grove Mine Mine ID 01-00851 CIVIL PENALTY PROCEEDING Docket No. SE 2009-487-P A.C. No. 01-00851-180940-01 Oak Grove Mine |
DECISION
Appearances:
Jennifer D. Booth, Esq., on behalf of the Secretary of Labor
R. Henry Moore, Esq., Jackson Kelly, PLLC, on behalf of Oak Grove Resources, LLC
Introduction:
These cases are before the Court on a notice of contest filed by the Respondent, Oak Grove Resources, LLC (“Oak Grove”) and a civil penalty petition filed by the Secretary of Labor (“Secretary”), acting on behalf of the Mine Safety and Health Administration (“MSHA”), pursuant to sections 105 and 110 of the Federal Mine Safety and Health Act of 1977, as amended. (“the Act”) (30 U.S.C. §§ 815, 820). In the Notice of Contest, the Contestant challenged, among other aspects, the validity of a safeguard, on several grounds. In the civil penalty proceeding, the Secretary, via a special assessment, seeks a $55,000.00 penalty on the basis of an alleged violation of 30 C.F.R. § 75.1403-10(b), a safeguard provision. A hearing was held in Birmingham, Alabama on December 7, 2011.
Background:
Miner Lee Graham was killed at Respondent’s Oak Grove Mine on May 22, 2008. There is no dispute about the circumstances of his death which may be briefly summarized as follows: On the date of Mr. Graham’s death, Oak Grove was in the process of transporting a shearer body to the longwall face via the main haulage road. The shearer body, a machine that operates on the longwall face, weighs 24 tons and at the time of the accident it was being transported on a “shearer carrier,” which is a haulage carrier designed for the task of hauling the shearer body. Mr. Graham died when he was pinned between a locomotive he was operating and the shearer body.
Oak Grove was attempting to transport the shearer body using two tandem locomotives: Motors No. 3 and No. 8, to pull the shearer carrier and Motors No. 4 and 9 to push the shearer carrier. Therefore in terms of their destination to the longwall, Motors No. 3 and 8, since they were pulling, were leading and Motors No. 4 and 9 were following the procession. Each pair of locomotives was connected to one another by a coupling. For the two coupled motors pulling the shearer body, No. 8 was in the lead, and connected to No. 3. The No. 3 itself was connected to the shearer body by a one inch diameter, flexible, wire rope. Thus, unlike the relatively rigid connection between the motors, through a coupling, the connection for the pulling locomotives, utilizing a wire rope to the shearer carrier was anything but rigid. Miner Graham was operating the No. 3 motor. In contrast to the wire rope arrangement connecting the pulling motors to the shearer carrier, the pushing motors were connected to the shearer carrier by a solid drawbar.
To recap, if one were standing alongside the transporting effort at the time, such individual would have observed, beginning at the front, pulling end, the No. 8 motor, which was connected to the No. 3 motor via a coupling and then the No. 3 motor connected to the shearer carrier by the wire rope. Next would be the shearer carrier itself and on the pushing end, a connection from it, by means of a solid drawbar, to the No. 4 motor. Finally, the No. 9 motor was connected to the No. 4 motor via a coupling in the same fashion as the link between the No. 3 and the No. 8. The significance of the wire rope connection will become apparent momentarily.
To understand how the fatality occurred, picture the procession moving towards its destination, as described, and reaching an upgrade. Slack then developed in the wire rope connection and the consequence was a derailment of the shearer carrier. Examining the situation, the victim unwittingly placed himself in a dangerous position, standing in the middle of the track, between his locomotive and the derailed shearer carrier. It was then that the coupled motors, Nos. 3 and 8 either slid or rolled downhill with Mr.Graham becoming fatally pinned between those motors and the shearer carrier.
An MSHA investigation ensued. This investigation was conducted by Inspector David Allen. Upon the conclusion of his investigation, Inspector Allen issued Citation No. 7696616, pursuant to Section 314(b) of the Mine Act for an alleged violation of Safeguard No. 2604892. In his testimony at the hearing, Mr. Allen spoke to the hazards arising from pushing cars on haulage roads. The hazards, he expressed, are plain. When one pushes a car visibility is affected because the load is in front of the pushing force. This makes it more difficult to see the track and any traffic that may lie ahead. Beyond that concern, when pushing, as opposed to pulling, one does not have positive control. Third, pushing also creates a pinch point, as happened here between the shearer carrier and the No. 3 motor.
The law regarding Safeguards:
The law regarding safeguards is well-established and clear. A few cases, representative of that law, are here noted.
In McElroy Coal, 23 FMSHRC 201 (Feb. 2001), Judge David F. Barbour, discussed this
issue where the mine challenged the validity of the underlying safeguard.
Judge Barbour noted that
the Commission has recognized that section 314(b) of the Mine Act “manifests a legislative purpose
to guard against all hazards attendant upon haulage and transportation in coal mining,” citing Jim
Walter Resources, Inc., 7 FMSHRC 493, 496 (April 1985), but that, because a safeguard is issued
without notice and comment rulemaking, the interpretation of them is more restrained. Further, he
observed that “the safeguard must identify with specificity the nature of the hazard involving the
transportation of miners or materials at which it is directed,” citing Southern Ohio Coal Co., 7
FMSHRC 509, 512 (“Southern Ohio Coal”). As the Commission expressly stated in Southern
Ohio Coal, “a safeguard notice must identify with specificity the nature of the hazard at which it is
directed and the conduct required of the operator to remedy such hazard.” Id. at 512. (emphasis
added). In that case, the safeguard spoke to fallen rock and cement blocks and required 24 inches of
clearance on both sides of the conveyor belt. Given those identified hazards, the Commission held
that “conditions such as the water described in the citation” were outside of the hazards identified in
the safeguard’s notice.
Judge Barbour also noted that, for all of these requirements, it is the Secretary that bears the
burden of proof in establishing the validity of the safeguard “by showing that the inspector evaluated
the specific conditions at the mine and determined that the safeguard was warranted in order to
address the actual transportation hazard.”
In Cyprus Cumberland Resources Corp.,19 FMSHRC 1781 (Nov. 1997), (“Cyprus”) the
Commission spoke to the subject of safeguards in a context similar to this case. There, signal lights
to control traffic were in issue.
Although the entire text of the safeguard was not stated in the
decision, the quoted portion of it is still informative. There it noted: “. . . track haulage
equip[ment]operators to use the block lights installed along supply track haulage at the mine, to
clear such lights (turn off after each use) in order to assure approaching haulage equipment a clear
road exists and also only 1 piece of haulage equipment shall be operated in the same block light
except [motors] . . . .” That safeguard was later modified, deleting the one piece of haulage
equipment being operated in a block requirement but adding a requirement that vehicles be
separated by at least 300 feet and that the signal light be used properly so that others would know
when other equipment was within a block. The Commission took the opportunity in Cyprus to
review the requirements for a valid safeguard, as set forth in Southern Ohio Coal Co., 14 FMSHRC
1, (January 1992)(“Socco II”). It noted that, in addition to the predicate requirement, that is, that
there be a transportation hazard not covered by a mandatory standard and that a safeguard is
necessary to correct the hazardous condition, the safeguard must state the corrective measures that
are to be taken.
In line with these requirements, the Commission added that such safeguards must be strictly construed, because they are issued without the usual practice of notice and comment rulemaking. Socco II, 14 FMSHRC 1, 8.
Oak Grove’s challenge to the validity of Safeguard No. 2604892.
Oak Grove has raised a number of challenges to MSHA’s enforcement action which will now be discussed.
Respondent contends that although the safeguard refers to a locomotive pushing two loaded
supply cars down grades, nowhere does it identify the nature of the hazard to which it was directed.
R’s Br. at 2. Looking to Commission precedent, Oak Grove asserts that the safeguard was not
validly issued. It notes that not only do Commission decisions in cases such as Socco II make this a
plain requirement for safeguards, but also that MSHA’s own Program Policy Manual (“PPM”)
directs that the “safeguard notice should also identify the nature of the hazard to which it is
directed.” Emphasizing this point, the PPM continues with an example of a potential subject for a
safeguard, adding that the “safeguard should also include a statement of the hazards that . . . [it] is
intended to prevent.” R’s Br. at 8-9, quoting 2003 PPM at p. 129. In fact, the safeguard notice in
issue in this litigation fails to expressly address any hazard. Thus, the Respondent urges that
because the safeguard in this case lacked the required specificity identifying the nature of the hazard,
it must fail. R’s Br. at 7-10. Accordingly, it is Respondent’s position that the Citation in issue in
this proceeding should be vacated because the underlying safeguard “fails to identify with specificity
the nature of the hazard at which it is directed.”
The government’s sole witness was David Allen, who is with the MSHA District Office in Birmingham, Alabama. Presently he is the supervisor, Mine Safety and Health Specialist for the ventilation plans group. Tr. 16. Allen was assigned to investigate the accident associated with this litigation. Tr. 19. Ex 4 is Allen’s accident investigation report. Tr. 20. According to Allen, as noted earlier, miners were in the process of moving the shearer carrier and, as they were traveling upgrade, slack developed in the wire rope between the No. 3 motor and the shearer carrier. With that slack, the carrier derailed. Allen agreed that once the shearer carrier derailed, the miners evaluated the problem. This took anywhere between two to five minutes and during that time the motors on either side of the shearer carrier did not move. At some point after that time elapsed Mr. Graham, the victim, stepped in between the shearer body and the No. 3 motor and it was then that the motor moved, resulting in Mr. Graham becoming fatally pinned between that motor and the shearer body. Tr. 56-57. Allen agreed that “one of the causal factors” was someone forgot to set a brake on the motors that moved. Tr. 58. Thus, apart from the safeguard’s failure to identify any hazard, and even if the Secretary’s claim as to the hazards supposedly addressed by the safeguard were accepted, this accident occurred not because of any claimed failure to comply with that safeguard. In short the accident did not occur from pushing the shearer.
Allen, who had prior mining experience moving mining equipment, stated that, when in his past work at mines, he had performed such tasks, the equipment was pulled through the mine. The pulling was accomplished by using a solid bar, that is a tongue or a drawbar between the locomotive and the car itself. Yet, he conceded, even when moving by pulling, derailments would occur. Tr. 28-29.
The safeguard, which was originally issued in March 1986, is set forth in GX 2. Tr. 40.
Allen offered his particular interpretation of the hazard the safeguard is intended to address. To that end, he described what the safeguard requires, that is, that cars on main haulage roads are
not to be pushed. Tr. 42. Distinct from that requirement, which is undeniably in the safeguard, is
the matter of the hazard. To deal with that, however, Allen moved from reading the text of the
safeguard to “the hazard that [he] identified in association with the safeguard.” That answer
required, not reading on Allen’s part, but reading into the hazard he assumed was intended by that
safeguard. Tr. 42. Allen then proceeded to identify “several hazards associated with [the
safeguard].” These included visibility hazards, the lack of “good positive control of the loads” by
pushing instead of pulling, and creating a “pinch point.” Tr. 42-44. To get right to the point, the
Court notes that not one of these hazards, or any other expressly stated hazard for that matter, is
within the four corners of the safeguard, and as such the safeguard is fatally flawed.
Nor is the
hazard so plainly obvious that it need not be stated.
It was brought out that during his investigation of the accident, Allen also issued two safeguard notices. Tr. 63. In contrast to the safeguard at issue here, Allen’s safeguards, one of which was based on 30 C.F.R. § 75.1403-10(b), described both the condition and the hazard he identified. Tr. 64. The other safeguard he issued did the same thing; it identified the hazard. Tr. 65. Further, Allen admitted that the safeguard in issue in this case does not describe the hazard. Tr. 65. Accordingly, when Allen was asked if the safeguard made any reference to “pinch points or visibility or the ability to control the load,” he responded: “No. I mean, it’s not in there.” Tr. 66. Allen admitted that when he writes a safeguard he always puts the hazard in it. Tr. 67.
For its part, the Secretary notes that the Act specifically provides for safeguards, per Section 314(b) of the Mine Act and that the provision allows the Secretary to issue “other safeguards adequate, in the judgment of an authorized representative . . . to minimize hazards with respect to transportation of men and materials.” Of course, no one disputes those observations. The Secretary acknowledges that the inspector must determine the presence of an actual transportation hazard, which hazard is not already addressed by another mandatory standard and that the safeguard is necessary to correct that hazard.
To the Respondent’s contention that the safeguard fails to specifically identify the hazard, the Secretary contends that the safeguard does sufficiently notify the mine of the hazardous conditions. Sec. Br. at 5. However, the Secretary’s admission that the hazard must be identified is not unqualified, as she argues that the safeguard does not require enumerating the specific hazards in it, such as the risk of one being crushed or struck. In its Reply Brief, the Secretary reiterates that point, asserting that the Commission has never invalidated a safeguard for failure to identify the specific hazards involved. Sec. Reply at 1. The test, it maintains, is that the safeguard adequately apprise the mine operator of the hazardous practice proscribed by it. Here, the Secretary believes, the safeguard could not be plainer: cars on main haulage roads are not to be pushed, period. The Secretary adds that is exactly what occurred with this fatality. The shearer carrier was being pushed, contrary to the safeguard’s prohibition of that practice. Thus, from the Secretary’s perspective, upholding the safeguard is a simple matter. The safeguard proscribes pushing cars and the Respondent’s Assistant General Mine Foreman/DayShift Foreman, Chad Johnson, admitted that the shearer carrier was being pushed as the shearer was being transported to the face. Sec. Br. at 7, citing Tr. 99. Therefore, it contends the Citation, No. 7696616, was established. As explained earlier, the Court has noted that Commission law requires more for a safeguard to be sustained.
CONCLUSION
In applying the law regarding safeguards to a specific enforcement action, here a section 104(a) citation, the determination of the applicability and validity of the safeguard must begin, and be bounded by, the four corners of the notice to provide safeguard. In this instance, the safeguard in question, which was issued on March 3, 1986 provided in full:
The No. 902 battery powered locomotive was being used to push
two loaded supply cars consisting of a car of timber and a car of
roof bolts down the graded haulage supply mine track entry of the
main south area of the mine, near the intersection of the No. 7 and
No. 14 section switch and the No. 10 and the No. 5 section switch.
Such area is approximately 2100 feet from the main bottom area of
the mine and approximately 3600 feet from the No. 7 section and
the No 10 sections. Respectively, this notice to provide safeguard
requires that cars on main haulage roads not be pushed except
where necessary to push cars from side tracks located near the
the working section to the producing entries and rooms.
Manifestly, the notice to provide safeguard fails to satisfy the requirements established by the
Commission because nowhere does it identify the hazard it purports to address. True, the
requirement is stated clearly that, with some exceptions, cars may not be pushed, but the hazard
from that activity is not stated. As such, applying the clear rules established by the Commission for
evaluating the validity of a safeguard, the safeguard issued here must fail.
The history of the safeguard in this case fails to comport with these requirements.
For the foregoing reasons, Oak Grove’s contest to Citation No. 7696616 is sustained and accordingly that Citation is hereby VACATED. Further, the Petition for the Assessment of Civil Penalty in Docket No. SE 2009-487-P is hereby DISMISSED.
William B. Moran
Administrative Law Judge
Distribution:
Jennifer Booth, Esq., Office of the Solicitor, U.S. Department of Labor, 618 Church Street, Suite 230, Nashville, TN 37219-2456
R. Henry Moore, Esq., Jackson Kelly, PLLC, Three Gateway Center, 401 Liberty Avenue, Suite 1340, Pittsburgh, PA 15222